CD74HCT174ME4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 25MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Number of Circuits | 7 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Propagation Delay | 40 ns |
| Turn On Delay Time | 17 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 6 |
| High Level Output Current | -4mA |
| Low Level Output Current | 4mA |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74HCT174ME4 Overview
It is embeded in SOIC case. The list contains 1 elements. A total of 16terminations have been recorded. A voltage of 5V provides power to the D latch. HCTis the family of this D flip flop. There is an electronic component mounted in the way of Surface Mount. With its 16pins, it is designed to work with most electronic flip flops. This device's clock edge trigger type is Positive Edge. This part is included in FF/Latches. Due to its superior flexibility, it uses 7 circuits. In view of its reliability, this D flip flop is a good fit for TUBE. The D latch operates on 5V volts. High efficiency requires the supply voltage to be maintained at 5V. As an additional reference, you may refer to electronic flip flop DUMMY VAL. -4mAis set as the high level output current. 4mAis set as the low level output current. The operating temperature should be lower than 125°C. Temperatures above -55°Cshould be used. In order for it to operate, a supply voltage of 4.5Vis required. It is capable of supporting a maximum supply voltage of 5.5V. It is possible to achieve 25MHz frequencies. It uses D FLIP-FLOPas its logic IC. There are 1 functions available on the JK flip flop. This device is equipped with a pin count of 16.
CD74HCT174ME4 Features
16 pins
5V power supplies
1 Functions
16 pin count
CD74HCT174ME4 Applications
There are a lot of Texas Instruments CD74HCT174ME4 Flip Flops applications.
- Shift Registers
- Balanced 24 mA output drivers
- Control circuits
- Convert a momentary switch to a toggle switch
- Circuit Design
- Memory
- Communications
- 2 – Bit synchronous counter
- Matched Rise and Fall
- Differential Individual
