CD74HCT174MT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Type | D-Type |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT174 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 4mA |
| Number of Bits | 6 |
| Clock Frequency | 25MHz |
| Propagation Delay | 40 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 17 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 40ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Number of Output Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT174MT Overview
The package is in the form of 16-SOIC (0.154, 3.90mm Width). D flip flop is included in the Tape & Reel (TR)package. Currently, the output is configured to use Non-Inverted. JK flip flop uses Positive Edgeas the trigger. There is an electronic component mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. -55°C~125°C TAis the operating temperature. The type of this D latch is D-Type. It belongs to the 74HCTseries of FPGAs. You should not exceed 25MHzin its output frequency. There are 1 elements in it. Currently, there are 16 terminations. You can search similar parts based on 74HCT174. An input voltage of 5Vpowers the D latch. A JK flip flop with a 10pFfarad input capacitance is used here. In this case, the D flip flop belongs to the HCTfamily. It is mounted by the way of Surface Mount. This board is designed with 16pins on it. It has a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. There are 6bits in this flip flop. The superior flexibility of this product is achieved by using 7 circuits. In view of its reliability, this D flip flop is a good fit for TR. The D latch operates on 5V volts. The supply voltage should be maintained at 5V for high efficiency. The 4mA output current allows it to be designed with the greatest amount of flexibility. To operate, the chip has a total of 6 output lines. As a result, it consumes 8μA of quiescent current without being affected by external factors. In addition, DUMMY VALis a characteristic of it.
CD74HCT174MT Features
Tape & Reel (TR) package
74HCT series
16 pins
6 Bits
5V power supplies
CD74HCT174MT Applications
There are a lot of Texas Instruments CD74HCT174MT Flip Flops applications.
- Cold spare funcion
- Guaranteed simultaneous switching noise level
- Power down protection
- Bounce elimination switch
- Parallel data storage
- Data transfer
- Load Control
- Asynchronous counter
- ESD protection
- Test & Measurement
