CD74HCT374M96
| Parameters | |
|---|---|
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 33 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 33ns @ 4.5V, 50pF |
| Prop. Delay@Nom-Sup | 50 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
CD74HCT374M96 Overview
The flip flop is packaged in 20-SOIC (0.295, 7.50mm Width). Package Cut Tape (CT)embeds it. It is configured with Tri-State, Non-Invertedas an output. In the configuration of the trigger, Positive Edgeis used. This electronic part is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. In the operating environment, the temperature is -55°C~125°C TA. This D latch has the type D-Type. It belongs to the 74HCTseries of FPGAs. There should be no greater frequency than 60MHzon its output. D latch consists of 1 elements. 20terminations have occurred. JK flip flop belongs to 74HCT374 family. It is powered from a supply voltage of 5V. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Devices in the HCTfamily are electronic devices. Electronic part Surface Mountis mounted in the way. A total of 20pins are provided on this board. This device has the clock edge trigger type of Positive Edge. This device is part of the FF/Latchesbase part number family. This flip flop is designed with 8 Bits. To achieve this superior flexibility, 8 circuits are used. On the basis of its reliable performance, this D flip flop is well suited for use with TR. The system runs on a power supply of 5V watts. There are 2 ports embedded in the flip flops. High efficiency requires the supply voltage to be maintained at 5V. There are no output lines on the JK flip flop. Quiescent current is consumed by the D latch in the amount of 8μA.
CD74HCT374M96 Features
Cut Tape (CT) package
74HCT series
20 pins
8 Bits
5V power supplies
CD74HCT374M96 Applications
There are a lot of Texas Instruments CD74HCT374M96 Flip Flops applications.
- Instrumentation
- Bounce elimination switch
- Guaranteed simultaneous switching noise level
- Circuit Design
- Data transfer
- Memory
- Latch
- ATE
- Parallel data storage
- Individual Asynchronous Resets
