CD74HCT4052E

SP4T 130Ohm Analog Switches BREAK-BEFORE-MAKE 74HCT4052 16 Pins 200nA 4.5V 16-DIP (0.300, 7.62mm)

Manufacturer: Texas Instruments
Nocochips NO: 815-CD74HCT4052E
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 297
Description: SP4T 130Ohm Analog Switches BREAK-BEFORE-MAKE 74HCT4052 16 Pins 200nA 4.5V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	ACTIVE (Last Updated: 6 days ago)
Contact Plating	Gold
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	951.693491mg
Operating Temperature	-55°C~125°C TA
Packaging	Tube
JESD-609 Code	e4
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	130Ohm
Subcategory	Multiplexer or Switches
Technology	CMOS
Number of Functions	1
Supply Voltage	4.5V
Base Part Number	74HCT4052
Pin Count	16
Operating Supply Voltage	5V
Polarity	Non-Inverting
Number of Channels	2
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	4.5V
Analog IC - Other Type	DIFFERENTIAL MULTIPLEXER
Nominal Supply Current	16μA
Number of Bits	4
Propagation Delay	12 ns
Turn On Delay Time	70 ns
Logic Function	Demultiplexer, Multiplexer
Number of Inputs	8
Voltage - Supply, Single/Dual (±)	4.5V~5.5V ±1V~5V
Supply Type	Dual, Single
Bandwidth	185MHz
Neg Supply Voltage-Nom (Vsup)	-4.5V
Turn-Off Delay Time	50 ns
Max Dual Supply Voltage	5V
On-State Resistance (Max)	130Ohm
Min Dual Supply Voltage	1V
High Level Output Current	25mA
Dual Supply Voltage	3V
Low Level Output Current	25mA
Multiplexer/Demultiplexer Circuit	4:1
Off-state Isolation-Nom	65 dB
Current - Leakage (IS(off)) (Max)	200nA
Channel Capacitance (CS(off), CD(off))	5pF 12pF
On-state Resistance Match-Nom	5Ohm
Switch Circuit	SP4T
Channel-to-Channel Matching (ΔRon)	5 Ω
Switching	BREAK-BEFORE-MAKE
Normal Position	NC
Height	5.08mm
Length	19.3mm
Width	6.35mm
Thickness	3.9mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

CD74HCT4052E Overview

The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have the same number of circuits 4:1. The operating temperature is extended to around -55°C~125°C TA. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 2 channels. With a 4.5V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 16 pins. Based on SP4T switching circuits, these analog multiplexers work. There are 2 circuits in this switch device. Use 74HCT4052 to search for variants of the digital switches. This digital multiplexer has 130Ohm internal resistance. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexers of the Dual, Single supply type that are cost-effective. A low voltage of 4.5V should be applied to the electronic component. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5V. A dual power supply should have at least 1V voltage attached. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. The electrical part can be operated at 5V voltage levels. The electrical component supports 8 inputs. There are 185MHz bandwidths for data transfer. 4-bit conductivity is possible.