CD74HCT4066E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 927.99329mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 95Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HCT4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 30 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 44 ns |
| On-State Resistance (Max) | 70Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Switch-off Time-Max | 53ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Drain to Source Resistance | 95Ohm |
| Normal Position | NO |
| Signal Current-Max | 0.25A |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT4066E Overview
The electronic component is convenient to ship overseas because it is packed in a 14-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around -55°C~125°C TA. In total, 14 terminations have occurred. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 4.5V voltage supply. An electrical component of this type can be found in the 14 series. These analog multiplexers are built based on SPST - NO switching circuits. Use 74HCT4066 to search for variants of the digital switches. An switch multiplexer with 95Ohm internal resistance has a value of 95Ohm. For details about the functions of 14 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Single supply type digital switch with a low cost. 4.5V should be the lowest voltage fed to the electronic component. This analog switch requires a voltage of 4.5V~5.5V to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 2μA. 5V operating voltages are supported by the electronic component. The transfer of data can be performed over 200MHz bandwidths. The Drain to Source resistance of this electronic component is 95Ohm.
CD74HCT4066E Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
Drain-to-Source resistance: 95Ohm
CD74HCT4066E Applications
There are a lot of Texas Instruments CD74HCT4066E Analog Switches & Multiplexers ICs applications.
- RGB switches
- Cell phones
- New designs requiring multiplexer functions
- E1 Multiplexer
- Ultrasound
- Access Concentrators
- Fault Tolerant Systems
- CSU
- Microprocessor Controlled Analog Systems
- Fiber to the Home
