CD74HCT4066M96
| Parameters | |
|---|---|
| Normal Position | NO |
| Signal Current-Max | 0.25A |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 95Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | 74HCT4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 30 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 46 ns |
| On-State Resistance (Max) | 70Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Switch-off Time-Max | 53ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
CD74HCT4066M96 Overview
Presented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Cut Tape (CT). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -55°C~125°C TA. In total, there are 14 terminations. High-quality output is provided by the electronic component's 4 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. A key feature of the 14 series is the inclusion of this electronic part as part of its design. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching with 74HCT4066 to find analog multiplexer variants. Analog switches have 95Ohm internal resistance. The functions of 14 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Single supply type analogue multiplexer. It is recommended to use 4.5V as the lowest voltage for the electrical part. Draining from a single voltage supply, this analog switch requires a voltage of 4.5V~5.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 2μA. Operating voltages of 5V are compatible with the electrical part. In 200MHz-bandwidths, data can be transferred.
CD74HCT4066M96 Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
CD74HCT4066M96 Applications
There are a lot of Texas Instruments CD74HCT4066M96 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- PDH Multiplexers
- Central office
- Sample hold systems
- New designs requiring multiplexer functions
- Remote Powered Equipment
- Routers
- PBXs
- High-Voltage
- Communication systems
