CD74HCT4066M96G4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | 74HCT4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 24 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 35 ns |
| On-State Resistance (Max) | 70Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Switch-off Time-Max | 53ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Normal Position | NO |
| Height | 1.58mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT4066M96G4 Overview
Presented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -55°C~125°C TA. In total, there have been 14 terminations. The electronic part delivers high-quality output through its 4 channels. Powered by a 4.5V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 14 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. Use 74HCT4066 to search for variants of the digital switches. There is 70Ohm internal resistance in this digital multiplexer. Datasheets for 14 pin functions are available upon request. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Digital switch that provides Single power at a cost-effective price. 4.5V is the lowest voltage the electrical component should receive. Analogue multiplexers require a 4.5V~5.5V voltage to drain from a single voltage supply. If you put voltage higher than 2μA on the digital multiplexer, damage may occur. The electronic component can function from 5V. A 200MHz-bandwidth can be used for data transfer.
CD74HCT4066M96G4 Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
CD74HCT4066M96G4 Applications
There are a lot of Texas Instruments CD74HCT4066M96G4 Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- USB 1.1 signal switching circuits
- Audio and video switching
- Transmit
- Fault Tolerant Systems
- Medical systems
- Precision test equipment
- Avionics test equipment
- Private Branch Exchange (PBX)
- Existing multiplexer applications (both fault-protected and nonfault-protected)
