Parameters |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Series |
Automotive, AEC-Q100 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
95Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
4.5V |
Base Part Number |
74HCT4066 |
Pin Count |
14 |
Operating Supply Voltage |
5V |
Polarity |
Non-Inverting |
Power Supplies |
5V |
Number of Channels |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4.5V |
Max Supply Current |
2μA |
Throw Configuration |
SPST |
Propagation Delay |
18 ns |
Turn On Delay Time |
24 ns |
Supply Type |
Single |
Bandwidth |
200MHz |
Turn-Off Delay Time |
35 ns |
On-State Resistance (Max) |
95Ohm |
High Level Output Current |
25mA |
Low Level Output Current |
25mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Channel Capacitance (CS(off), CD(off)) |
5pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
24ns, 35ns |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-72dB @ 1MHz |
Switching |
MAKE-BEFORE-BREAK |
Switch-on Time-Max |
36ns |
Switch-off Time-Max |
53ns |
Voltage - Supply, Single (V+) |
4.5V~5.5V |
Normal Position |
NO |
Signal Current-Max |
0.25A |
Height |
1.2mm |
Length |
5mm |
Width |
4.4mm |
Thickness |
1mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Weight |
56.812444mg |
CD74HCT4066QPWRQ1 Overview
Packed in 14-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. In total, there have been 14 terminations. Due to its 4 channels, the electrical component produces high-quality output. A 4.5V voltage supply should turn on and run the electronic component. A key feature of the 14 series is the inclusion of this electronic part as part of its design. Unlike digital switches, these are based on SPST - NO switching circuits. Search with 74HCT4066 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 95Ohm. You can find the functions of the 14 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 4.5V. A voltage of 4.5V~5.5V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 2μA. 5V operating voltages are supported by the electronic component. There are 200MHz bandwidths for data transfer. This is one of the Automotive, AEC-Q100 series.
CD74HCT4066QPWRQ1 Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
CD74HCT4066QPWRQ1 Applications
There are a lot of Texas Instruments CD74HCT4066QPWRQ1 Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- PDAs
- Fiber to the Home
- CSU
- Battery Powered Instruments
- Multiplexers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- New designs requiring multiplexer functions
- Cable Modem
- Microwave transmission systems