CD74HCT74M96G4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 50MHz |
| Propagation Delay | 35 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 35 ns |
| Family | HCT |
| Logic Function | AND, D-Type |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 35ns @ 4.5V, 50pF |
| Prop. Delay@Nom-Sup | 53 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT74M96G4 Overview
The flip flop is packaged in 14-SOIC (0.154, 3.90mm Width). A package named Tape & Reel (TR)includes it. As configured, the output uses Differential. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. A temperature of -55°C~125°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. This D flip flop should not have a frequency greater than 50MHz. 14terminations have occurred. You can search similar parts based on 74HCT74. An input voltage of 5Vpowers the D latch. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. HCTis the family of this D flip flop. It is mounted by the way of Surface Mount. There are 14pins on it. This device has the clock edge trigger type of Positive Edge. This part is included in FF/Latches. In order to achieve its superior flexibility, 2 circuits are used. On the basis of its reliable performance, this D flip flop is well suited for use with TR. In order for the device to operate, it requires 5V power supplies. High efficiency requires the supply voltage to be maintained at 5V. In order to operate, the chip has 1 output lines. It consumes 4μA of quiescent current without being affected by external factors.
CD74HCT74M96G4 Features
Tape & Reel (TR) package
74HCT series
14 pins
5V power supplies
CD74HCT74M96G4 Applications
There are a lot of Texas Instruments CD74HCT74M96G4 Flip Flops applications.
- Synchronous counter
- Matched Rise and Fall
- ESCC
- Patented noise
- Divide a clock signal by 2 or 4
- Storage Registers
- Power down protection
- Count Modes
- 2 – Bit synchronous counter
- Control circuits
