CDC2509CPW
| Parameters | |
|---|---|
| Lifecycle Status | NRND (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 24 |
| Weight | 89.499445mg |
| Operating Temperature | 0°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | PLL Clock Driver |
| Subcategory | Clock Drivers |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 125MHz |
| Base Part Number | CDC2509 |
| Pin Count | 24 |
| Number of Outputs | 9 |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Load Capacitance | 30pF |
| Nominal Supply Current | 10μA |
| Power Dissipation | 700mW |
| Output Characteristics | SERIES-RESISTOR |
| Input | LVTTL |
| Ratio - Input:Output | 1:9 |
| PLL | Yes with Bypass |
| Differential - Input:Output | No/No |
| Same Edge Skew-Max (tskwd) | 0.2 ns |
| Height | 1.2mm |
| Length | 7.8mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CDC2509CPW Overview
Clock generator is packaged in the way of Tube. This clock generator is embedded in the 24-TSSOP (0.173, 4.40mm Width) package. The peak reflow temperature (Cel) amounts to 260 to be essentially indestructible. As a result of this, we can find 24 terminations. For this clock generator ic, a voltage of 3.3V is required. As the Clock PLL's input, LVTTL is designed to be used in order to generate the clock signal. Using 1 circuits, the electronic part's full performance can be accessed. The Surface Mount allows this electrical component to be easily installed on the panel. Approximately 3.6V is the maximum supply voltage needed by this time clock generator. In order to maintain safety, this frequency generator should be supplied with voltages above 3V. There are 3V~3.6V available for use with this clock PLL. Using the test statistics, it is estimated that the ambient temperature should be set to 0°C~85°C. A PLL Clock Driver is a classification for the electronic part in question. It is a 24-bit clock PLL designed specifically for microprocessors. The related electrical components for the base part number CDC2509 can be found below. It is possible to connect to the frequency generators via 24 pins. Time clock generator is capable of handling a voltage of 3.3V. In general, this clock PLL is considered a Clock Drivers device. The output frequency is magnified as high as possible with 9 signal outputs. The timing skew of this frequency synthesizer is low at 0.2 nsmax. It is able to realize high efficiency when operating at a frequency of 125MHz. In other words, PLL is capable of delivering a load capacitance of 30pF.
CDC2509CPW Features
Available in the 24-TSSOP (0.173, 4.40mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
Load capacitance of 30pF
CDC2509CPW Applications
There are a lot of Texas Instruments CDC2509CPW Clock Generators applications.
- FMCW Radar
- Automatic test equipment
- Ultrasound diagnosis
- Signal analyzer
- Set-top boxes
- Local oscillators (LOs)
- Frequency Modulation (FM) stereo decoders
- Tracking filters
- Electronic countermeasures
- Satellite navigation communication
