CDCE706PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | Spread Spectrum Clock Driver |
| Max Power Dissipation | 600mW |
| Technology | BICMOS |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Frequency | 54MHz |
| Base Part Number | CDCE706 |
| Output | LVCMOS |
| Pin Count | 20 |
| Number of Outputs | 6 |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 3 |
| Interface | I2C |
| Number of Circuits | 1 |
| Nominal Supply Current | 90mA |
| Frequency (Max) | 300MHz |
| Input | LVCMOS, Crystal |
| Ratio - Input:Output | 1:6 |
| Primary Clock/Crystal Frequency-Nom | 200MHz |
| PLL | Yes with Bypass |
| Differential - Input:Output | Yes/No |
| Divider/Multiplier | Yes/Yes |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CDCE706PWR Overview
As a clock IC, it is packaged by the Tape & Reel (TR) method. The 20-TSSOP (0.173, 4.40mm Width) package includes this clock generator. Under reflowing process, this clock generator ic is able to sustain a maximum temperature of 260. In it, there are 20 terminations to be found. For this clock generator ic, a voltage of 3.3V is required. In this case, LVCMOS, Crystal is designed to be the input of the clock generator. A total of 1 circuits are implemented to access the full performance of the electrical part. An upper frequency limit of 300MHz Max can be achieved with this clock-based frequency synthesizer. The Surface Mount allows this electrical component to be easily installed on the panel. As far as the supply voltage is concerned, clock PLL can be used with 3V~3.6V. As determined by the test statistics, the ambient temperature should be set to -40°C~85°C. The RF synthesizer is compatible with LVCMOS logic levels. As far as electrical parts go, this component can be classified as a Spread Spectrum Clock Driver component. An IC that generates clocks specifically for microprocessors, this clock PLL is 20-bits in si20e. The related electronic parts of part number CDCE706 are listed below. There are a number of 20 pins that are available on the clock generators. Electronic frequency generator can handle voltages up to 3.3V. 6 signal outputs are provided for enhancing output frequency as much as possible. Frequency generator is able to reali54MHze high efficiency when operating at a frequency of 54MHz. In this case, we are looking at a frequency generator with 3 elements that is low-jitter.
CDCE706PWR Features
Available in the 20-TSSOP (0.173, 4.40mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
CDCE706PWR Applications
There are a lot of Texas Instruments CDCE706PWR Clock Generators applications.
- Signal generator
- Integrated phase noise in aerospace systems
- Pagers
- Skew suppression
- Smartphones
- Signal demodulation
- Myriad digital applications
- Carrier synchronization in wired communication
- Deep space exploration
- Microwave backhaul IF
