CDCV850DGGR
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 2 weeks ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 48 |
| Weight | 223.195796mg |
| Operating Temperature | 0°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 48 |
| Type | PLL Clock Driver |
| Subcategory | Clock Drivers |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2.3V~2.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Frequency | 140MHz |
| Base Part Number | CDCV850 |
| Output | SSTL-2 |
| Pin Count | 48 |
| Number of Outputs | 10 |
| Operating Supply Voltage | 2.5V |
| Supply Voltage-Max (Vsup) | 2.7V |
| Power Supplies | 2.52.5/3.3V |
| Supply Voltage-Min (Vsup) | 2.3V |
| Number of Circuits | 1 |
| Nominal Supply Current | 6mA |
| Family | 850 |
| Input | LVTTL, SSTL-2 |
| Ratio - Input:Output | 1:11 |
| PLL | Yes with Bypass |
| Differential - Input:Output | Yes/Yes |
| Propagation Delay (tpd) | 4 ns |
| Divider/Multiplier | No/No |
| Same Edge Skew-Max (tskwd) | 0.075 ns |
| Height | 1.2mm |
| Length | 12.5mm |
| Width | 6.1mm |
| Thickness | 1.15mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CDCV850DGGR Overview
A clock integrated circuit is packaged in a Tape & Reel (TR)-shaped package because it is for use as a clock. The 48-TFSOP (0.240, 6.10mm Width) package contains this clock generator. In the reflowing process, this clock generator ic is able to maintain a maximum temperature of 260. It contains a total of 48 terminations within RF synthesizer. To operate this time clock generator, 2.5V voltage should be applied. In this case, LVTTL, SSTL-2 is designed to be the input of the clock generator. An implementation of 1 circuits is required in order to fully utili1e the capabilities of the electrical part. The Surface Mount allows this electrical component to be easily installed on the panel. The maximal supply voltage this clock generator would take is 2.7V. The supply voltage for this frequency synthesizer should be kept above 2.3V for safety considerations. As far as the supply voltage is concerned, clock PLL can be used with 2.3V~2.7V. Statistics suggest that the ambient temperature be set at 0°C~85°C, which is what is estimated by the test. There are several logic levels in SSTL-2 logic that can be used with this clock generator. This electronic component can be classified into PLL Clock Driver. It is a 48-bit IC that is designed for microprocessors specifically. CDCV850 is the base part number for finding related electronic parts. PF synthesizers is equipped with 48 pins. The maximum supply voltage that analog clock generator can handle is 2.5V. A Clock Drivers clock generator is essentially what this device is. 10 signal outputs enable clock PLL to magnify output frequency as high as possible. The maximal same edge skew (tskwd) can not be exceeded. By searching for parts that belong to the 850 family, you can find electronic parts that are similar. By operating at a frequency of 140MHz, frequency generator is able to achieve high efficiency. There is no doubt that the TR package is an ideal fit for this clock generator ic.
CDCV850DGGR Features
Available in the 48-TFSOP (0.240, 6.10mm Width)
Supply voltage of 2.5V
Operating supply voltage of 2.5V
CDCV850DGGR Applications
There are a lot of Texas Instruments CDCV850DGGR Clock Generators applications.
- Time to digital converters
- Test and instrumentation equipment
- Reference signals to RF systems
- Modems
- Radiotelephones
- Signal generator
- Mechanical devices
- Mixed mode (analog and digital) applications
- Wide area power system
- PMR (Professional Mobile Radio)
