banner_page

CDCV857DGGR

2.5V PLL Clock Driver CDCV857 Clock Generators 48 Pins 48-TFSOP (0.240, 6.10mm Width) 48 Terminals Surface Mount 2.3V~2.7V Cut Tape (CT)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-CDCV857DGGR
  • Package: 48-TFSOP (0.240, 6.10mm Width)
  • Datasheet: PDF
  • Stock: 859
  • Description: 2.5V PLL Clock Driver CDCV857 Clock Generators 48 Pins 48-TFSOP (0.240, 6.10mm Width) 48 Terminals Surface Mount 2.3V~2.7V Cut Tape (CT) (Kg)

Details

Tags

Parameters
Contact Plating Gold
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 48-TFSOP (0.240, 6.10mm Width)
Number of Pins 48
Weight 223.195796mg
Operating Temperature 0°C~85°C
Packaging Cut Tape (CT)
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 2 (1 Year)
Number of Terminations 48
Type PLL Clock Driver
Voltage - Supply 2.3V~2.7V
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 2.5V
Terminal Pitch 0.5mm
Frequency 200MHz
Base Part Number CDCV857
Pin Count 48
Number of Outputs 10
Operating Supply Voltage 2.5V
Supply Voltage-Max (Vsup) 2.7V
Supply Voltage-Min (Vsup) 2.3V
Number of Circuits 1
Nominal Supply Current 275mA
Family 857
Output Characteristics 3-STATE
Input Clock
Ratio - Input:Output 1:10
PLL Yes with Bypass
Differential - Input:Output Yes/Yes
Propagation Delay (tpd) 4.5 ns
Divider/Multiplier No/No
Same Edge Skew-Max (tskwd) 0.075 ns
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

CDCV857DGGR Overview


Clock generator is packaged in the way of Cut Tape (CT). This clock generator is embedded in the 48-TFSOP (0.240, 6.10mm Width) package. Under reflowing process, this clock generator ic is able to sustain a maximum temperature of 260. As you can see, it consists of 48 terminations. A voltage of 2.5V should be applied to this electronic frequency generator. There is a Clock PLL called Clock which is designed to be the input to this clock generator. An implementation of 1 circuits is required in order to fully utili1e the capabilities of the electrical part. The Surface Mount allows this electrical component to be easily installed on the panel. Approximately 2.7V is the maximum supply voltage needed by this time clock generator. It is safe to use this frequency synthesizer with a supply voltage above 2.3V. Clock generator ic works with 2.3V~2.7V. Based on the test statistics, an ambient temperature of 0°C~85°C should be set. This is an electronic part that can be classified as a PLL Clock Driver in this case. In particular, this clock PLL is designed to be used with microprocessors. This part number CDCV857 is related to the following electrical components. The frequency synthesizer has 48 pins that are available. Supply voltage 2.5V is what clock generator can handle. Clock PLL is facilitated with 10 signal outputs to magnify output frequency as high as possible. This clock generator offers low timing skew at 0.075 ns Max. When searching for parts belonging to the 857 family, similar electric components can be found. Frequency generator is able to reali200MHze high efficiency when operating at a frequency of 200MHz.

CDCV857DGGR Features


Available in the 48-TFSOP (0.240, 6.10mm Width)
Supply voltage of 2.5V
Operating supply voltage of 2.5V

CDCV857DGGR Applications


There are a lot of Texas Instruments CDCV857DGGR Clock Generators applications.

  • Myriad digital applications
  • Microwave backhaul IF
  • Vector network analyzers (VNA)
  • CB radios
  • PCI express cards
  • Local oscillators (LOs)
  • Clock synchronization
  • Radiotelephones
  • Automatic test equipment
  • Smartphones

Write a review

Note: HTML is not translated!
    Bad           Good