CDCVF2510APWRG4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 24 |
| Weight | 89.499445mg |
| Operating Temperature | 0°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | PLL Clock Driver |
| Subcategory | Clock Drivers |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 175MHz |
| Base Part Number | CDCVF2510 |
| Pin Count | 24 |
| Number of Outputs | 10 |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Nominal Supply Current | 40μA |
| Input | LVTTL |
| Ratio - Input:Output | 2:11 |
| PLL | Yes with Bypass |
| Differential - Input:Output | No/No |
| Prop. Delay@Nom-Sup | 3.9 ns |
| Propagation Delay (tpd) | 3.9 ns |
| Length | 7.8mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CDCVF2510APWRG4 Overview
The Tape & Reel (TR) method is used for packaging clock ICs. The 24-TSSOP (0.173, 4.40mm Width) package embeds this Clock PLL. The frequency generator is capable of withstanding a maximum temperature of 260 during reflowing. As a result, frequency synthesizers can be found to contain 24 terminations. This time clock generator should be voltaged at 3.3V. This clock generator receives its inputs from LVTTL, which is designed to be the clock source. A total of 1 circuits are implemented to access the full performance of the electrical part. The Surface Mount allows the electrical component to be installed conveniently on the panel. Clock PLL is capable of receiving a maximum of 3.6V as a supply voltage. For safety reasons, this frequency generator's supply voltage should remain above 3V. Clock generator ic works with 3V~3.6V. The ambient temperature should be set at 0°C~85°C, which is estimated by the test statistics. This electronic component is usually classified as a PLL Clock Driver component. It is a 24-bit clock PLL designed specifically for microprocessors. Related electrical parts can be found for the base part number CDCVF2510. A 24 pin is available on the PLL. Supply voltage 3.3V is what time clock generator can handle. The clock PLL is generally classified as a Clock Drivers device. The output frequency can be amplified as high as possible with its 10 signal outputs. Using a frequency of 175MHz allows frequency synthesizer to achieve high efficiencies.
CDCVF2510APWRG4 Features
Available in the 24-TSSOP (0.173, 4.40mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
CDCVF2510APWRG4 Applications
There are a lot of Texas Instruments CDCVF2510APWRG4 Clock Generators applications.
- Time to digital converters
- High-speed communication applications
- Microwave point-to-point systems
- Carrier synchronization in wired communication
- Televisions
- Space communucation
- Frequency Modulation (FM) stereo decoders
- 1 Gigabit Ethernet
- CPUs
- MRI
