CDCVF857RHAR
| Parameters | |
|---|---|
| Number of Outputs | 10 |
| Operating Supply Voltage | 2.5V |
| Supply Voltage-Max (Vsup) | 2.7V |
| Supply Voltage-Min (Vsup) | 2.3V |
| Number of Circuits | 1 |
| Nominal Supply Current | 10mA |
| Family | 857 |
| Output Characteristics | 3-STATE |
| Input | SSTL-2 |
| Ratio - Input:Output | 2:11 |
| PLL | Yes with Bypass |
| Differential - Input:Output | Yes/Yes |
| Propagation Delay (tpd) | 3.5 ns |
| Divider/Multiplier | No/No |
| Same Edge Skew-Max (tskwd) | 0.04 ns |
| Length | 6mm |
| Width | 6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 40-VFQFN Exposed Pad |
| Number of Pins | 40 |
| Weight | 103.986051mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 40 |
| ECCN Code | EAR99 |
| Type | PLL Clock Driver |
| Subcategory | Clock Drivers |
| Voltage - Supply | 2.3V~2.7V |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Frequency | 220MHz |
| Base Part Number | CDCVF857 |
| Pin Count | 40 |
CDCVF857RHAR Overview
Clock generator is packaged in the way of Tape & Reel (TR). Embedded in the 40-VFQFN Exposed Pad package is this Clock PLL. This clock generator ic can sustain 260 degrees of temperature during reflowing. As a result of this, we can find 40 terminations. A voltage of 2.5V should be applied to this electronic frequency generator. As the Clock PLL's input, SSTL-2 is designed to be used in order to generate the clock signal. 1 circuits are implemented to access the electronic component's full performance. Surface Mount-slots make it easy to mount this electronic component on panels. 2.7V would be the maximum supply voltage for this clock generator. The supply voltage (Vsup) should be kept above 2.3V for normal operation. This clock PLL works with a supply voltage of 2.3V~2.7V. Statistics suggest that the ambient temperature be set at -40°C~85°C, which is what is estimated by the test. A PLL Clock Driver is a classification for the electronic part in question. In particular, this clock PLL is designed to be used with microprocessors. These related electrical parts are available for the base part number CDCVF857. The clock PLL has 40 pins that are available. There is a maximum supply voltage of 2.5V that clock generator can handle. Clock generator can also be included into Clock Drivers. The output frequency can be magnified as high as possible with the assistance of 10 signal outputs. Low timing skew is provided by this analog clock generator at maximum 0.04 ns. 857-family clock generators are similar. At a frequency of 220MHz, frequency generator is capable of achieving high efficiency.
CDCVF857RHAR Features
Available in the 40-VFQFN Exposed Pad
Supply voltage of 2.5V
Operating supply voltage of 2.5V
CDCVF857RHAR Applications
There are a lot of Texas Instruments CDCVF857RHAR Clock Generators applications.
- Clock synchronization
- Automatic control
- Digital circuits
- Notebooks
- Microwave point-to-point systems
- Electronic equipment
- 1 Gigabit Ethernet
- Closed circuit systems
- Simple clock clean-up circuits
- Myriad digital applications
