CS5124XDR8
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Frequency | 50kHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | CS5124 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 20V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 20V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 7.7V~20V |
| Control Features | Soft Start |
| Input Voltage (Min) | 7.6V |
| Topology | Flyback, Forward Converter |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 400kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 45ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 25 ns |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 82.5% |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
CS5124XDR8 Overview
With a 8-SOIC (0.154, 3.90mm Width) package, the switching controller is suitable for a wide range of applications. 1 outputs can be generated with the dc motor controller. Tape & Reel (TR) solid enclosure protects the pmic. Transistor Driver dc switching's outputs (s) can be handled by it. 7.7V~20V is the supply voltage and the operating voltage of the dc control. Suitable for a -40°C~105°C TA dc switcher. The switching controller can be switched at 400kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. Featured in the dcdc regulator is Soft Start which allows efficient switching control. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. DUAL are the position of the terminal of the switching converters. A variety of terminations with 8 of dc switching. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 12V. Other relevant dc to dc converter ics will be returned if you search "CS5124". Pins number 8 of switching converter in total. Specifically, switching converter falls under the Switching Regulator or Controllers category. Input voltage of dc dc voltage regulator should be 7.6V. DC regulator outputs 20V voltage based on test statistics. A starting point for a project is to note down the dc dc regulator's usual output current, which is 200mA. Switching controller operates at 50kHz Hz. If the user wishes to run the voltage regulator dc to dc in a circuit safely and reliably, they should apply 20V.
CS5124XDR8 Features
Transistor Driver Outputs
Switching Frequency: 400kHz
Soft Start
PULSE WIDTH MODULATION
Frequency: 50kHz
CS5124XDR8 Applications
There are a lot of ON Semiconductor CS5124XDR8 DC to DC converter applications.
- Automatic testing equipment
- Smoke prevention equipment
- Telecommunications equipment
- Die casting equipment
- Driver circuits
- Lathes
- Linear guide
- Emergency lighting monitoring equipment
- Wide-range voltage regulation circuits
- Post equipment
