CY2292FXI
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Clock Generator, Fanout Distribution |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Clock Generators |
| Voltage - Supply | 3.3V 5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Frequency | 80MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | CY2292 |
| Output | CMOS |
| Pin Count | 16 |
| Number of Outputs | 6 |
| Operating Supply Voltage | 5V |
| Number of Elements | 3 |
| Number of Circuits | 1 |
| Nominal Supply Current | 110mA |
| Max Supply Current | 110mA |
| Frequency (Max) | 60MHz 80MHz |
| Input | Clock, Crystal |
| Ratio - Input:Output | 1:6 |
| Primary Clock/Crystal Frequency-Nom | 30MHz |
| PLL | Yes |
| Differential - Input:Output | No/No |
| Divider/Multiplier | Yes/No |
| Height | 1.48mm |
| Length | 9.98mm |
| Width | 3.98mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY2292FXI Overview
The Tube method is used for packaging clock ICs. Clock PLL is embedded in the 16-SOIC (0.154, 3.90mm Width) package. This clock generator will sustain a maximum temperature of 260 when reflown. 16 terminations can be found in frequency synthesizer. Basically, a voltage of 5V should be applied to this electronic frequency generator. Clock, Crystal is designed for clock generator's input. An implementation of 1 circuits is required in order to fully utili1e the capabilities of the electrical part. Using this clock-based frequency synthesizer, you can achieve a maximum frequency of 60MHz 80MHz. Due to the Surface Mount-shape, this electronic component can be conveniently installed on the panel. There should be 3.3V 5V provided with this RF synthesizer. Test statistics estimate a temperature of -40°C~85°C, which should be set as the ambient temperature. CMOS is designed for clock generator's output. Clock Generator, Fanout Distribution is the type of electrical part that this component is classified as. The clock-generating IC is a 16-bit device designed specifically for microprocessors. The related electronic parts of part number CY2292 are listed below. It is possible to connect to the PLL via 16 pins. There is a maximum supply voltage of 5V that this analog clock generator can handle. This clock generator can be classified as a kind of Clock Generators in general. The output frequency is magnified as high as possible with 6 signal outputs. High efficiency is achieved when operating at a frequency of 80MHz. An 8-element clock PLL with a low jitter performance is available on this page. In this RF synthesizer operation, 110mA of current are supplied.
CY2292FXI Features
Available in the 16-SOIC (0.154, 3.90mm Width)
Supply voltage of 5V
Operating supply voltage of 5V
CY2292FXI Applications
There are a lot of Cypress Semiconductor Corp CY2292FXI Clock Generators applications.
- Signal frequency synthesis circuits
- Reference signals to RF systems
- Local oscillators (LOs)
- Wide area power system
- Clock recovery
- Closed circuit systems
- Signal demodulation
- Communication infrastructure
- Microwave radio
- Radiotelephones
