CY2309CZXI-1HT
| Parameters | |
|---|---|
| Differential - Input:Output | No/No |
| Propagation Delay (tpd) | 8.7 ns |
| Same Edge Skew-Max (tskwd) | 0.2 ns |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Gold, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| Type | Fanout Buffer (Distribution), Zero Delay Buffer |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Clock Drivers |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | CY2309 |
| Output | LVCMOS |
| Pin Count | 16 |
| Number of Outputs | 9 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Nominal Supply Current | 35mA |
| Frequency (Max) | 133.33MHz |
| Input | LVCMOS, LVTTL |
| Ratio - Input:Output | 1:9 |
| PLL | Yes with Bypass |
CY2309CZXI-1HT Overview
Clock ICs are packaged using the Tape & Reel (TR) method. The 16-TSSOP (0.173, 4.40mm Width) package includes this clock generator. The peak reflow temperature (Cel) amounts to 260 to be essentially indestructible. In it, there are 16 terminations to be found. The clock generator ic should be grounded with a voltage of 3.3V. This Clock PLL will be fed by LVCMOS, LVTTL as its input. An implementation of 1 circuits is required in order to fully utili1e the capabilities of the electrical part. It provides a maximum frequency of 133.33MHz. Thanks to the Surface Mount, this electric component can be conveniently installed on the panel. It would be possible to supply this clock PLL with 3.6V of power. A maximum voltage of 3V should be used for this frequency generator for safety reasons. Clock PLL works with 3V~3.6V supply voltage provided. Using the test statistics, it is estimated that the ambient temperature should be set to -40°C~85°C. A frequency synthesizer which is compatible with the LVCMOS logic levels is presented here. It has been classified as a Fanout Buffer (Distribution), Zero Delay Buffer electronic part, which means that it is a semiconductor. Microprocessor-specific clock PLL with 16 bits. You can find related electrical components to the base part number CY2309. There are 16 pins that are available on the frequency generator. In terms of the supply voltage, PLL clock can handle 3.3V volts. Clock Drivers-type frequency generators are usually classified as this type. The output frequency is magnified as high as possible with 9 signal outputs. This clock generator offers low timing skew at 0.2 ns Max.
CY2309CZXI-1HT Features
Available in the 16-TSSOP (0.173, 4.40mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
CY2309CZXI-1HT Applications
There are a lot of Cypress Semiconductor Corp CY2309CZXI-1HT Clock Generators applications.
- FM demodulation networks for FM operations
- Electronic equipment
- FSK demodulators
- 1 Gigabit Ethernet
- Signal frequency synthesis circuits
- Simple clock clean-up circuits
- Frequency synthesis
- Sampling clocks for ADC and DAC
- Cell phones
- Clock synchronization
