CY2309SXI-1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| Type | Fanout Buffer (Distribution), Zero Delay Buffer |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Clock Drivers |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Frequency | 133.33MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | CY2309 |
| Output | LVCMOS |
| Pin Count | 16 |
| Number of Outputs | 9 |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Nominal Supply Current | 35mA |
| Input | LVCMOS, LVTTL |
| Ratio - Input:Output | 1:9 |
| Max I(ol) | 0.008 A |
| PLL | Yes with Bypass |
| Differential - Input:Output | No/No |
| Propagation Delay (tpd) | 8.7 ns |
| Same Edge Skew-Max (tskwd) | 0.25 ns |
| Height | 1.48mm |
| Length | 9.98mm |
| Width | 3.98mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY2309SXI-1 Overview
As a clock IC, PLLs is packaged using the Tube method. There is a clock generator embedded in the 16-SOIC (0.154, 3.90mm Width) package. Frequency generator can maintain a maximum temperature of 260 under reflowing conditions. It contains a total of 16 terminations within RF synthesizer. For this clock generator ic, a voltage of 3.3V is required. A clock generator's input is called LVCMOS, LVTTL and it is designed as the input for this clock generator. To access the electronic component's full performance, 1 circuits are implemented. Thanks to the Surface Mount, this electric component can be conveniently installed on the panel. It would be possible to supply this clock PLL with 3.6V of power. For safety reasons, this frequency synthesizer should have a voltage supply above 3V. Clock generators should operate with the voltage supply of 3V~3.6V. As determined by the test statistics, the ambient temperature should be set to -40°C~85°C. In this case, we are dealing with a frequency synthesizer that can be used with LVCMOS logic levels. As far as this electronic part is concerned, it can be classified as a Fanout Buffer (Distribution), Zero Delay Buffer component. In this IC, a 16-bit frequency generator is designed specifically for use in microprocessors. It is possible to find its related electronic parts by searching for the base part number CY2309. Clock generator is designed with 16 pins. In terms of the supply voltage, PLL clock can handle 3.3V volts. In general, this clock PLL is considered a Clock Drivers device. Clock PLL is facilitated with 9 signal outputs to magnify output frequency as high as possible. Low timing skew is offered by this RF synthesizer at maximum 0.25 ns. By operating at a frequency of 133.33MHz, frequency generator is able to achieve high efficiency.
CY2309SXI-1 Features
Available in the 16-SOIC (0.154, 3.90mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
CY2309SXI-1 Applications
There are a lot of Cypress Semiconductor Corp CY2309SXI-1 Clock Generators applications.
- Instrument
- Clock recovery
- Telecommunication systems
- Clock generation systems
- Digital circuits
- CPUs
- Digital switching systems
- Signal modulation and demodulation
- FPGA and processor clocks
- Radio receivers
