CY74FCT2374ATQCT
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 20 |
| Weight | 125.786834mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT2374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 12mA |
| Number of Bits | 8 |
| Clock Frequency | 250MHz |
| Propagation Delay | 6.5 ns |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 200μA |
| Current - Output High, Low | 15mA 12mA |
| Max Propagation Delay @ V, Max CL | 6.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY74FCT2374ATQCT Overview
It is embeded in 20-SSOP (0.154, 3.90mm Width) case. It is contained within the Tape & Reel (TR)package. T flip flop uses Tri-State, Non-Invertedas its output configuration. It is configured with a trigger that uses Positive Edge. This electronic part is mounted in the way of Surface Mount. The supply voltage is set to 4.75V~5.25V. It is operating at a temperature of -40°C~85°C TA. D-Typedescribes this flip flop. In FPGA terms, D flip flop is a type of 74FCTseries FPGA. A frequency of 250MHzshould be the maximum output frequency. A total of 1elements are present in it. As a result, it consumes 200μA quiescent current. It has been determined that there have been 20 terminations. D latch belongs to the 74FCT2374 family. An input voltage of 5Vpowers the D latch. A JK flip flop with a 5pFfarad input capacitance is used here. FCTis the family of this D flip flop. It is mounted by the way of Surface Mount. A total of 20pins are provided on this board. This device exhibits a clock edge trigger type of Positive Edge. It is included in FF/Latches. It is designed with 8bits. Due to its superior flexibility, it uses 8 circuits. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. An electrical current of 5V volts is applied to it. A total of 2ports are embedded in the D flip flop. The supply voltage should be maintained at 5V for high efficiency. In addition to its maximum design flexibility, the output current of the T flip flop is 12mA. The JK flip flop is with 3 output lines to operate.
CY74FCT2374ATQCT Features
Tape & Reel (TR) package
74FCT series
20 pins
8 Bits
5V power supplies
CY74FCT2374ATQCT Applications
There are a lot of Texas Instruments CY74FCT2374ATQCT Flip Flops applications.
- Parallel data storage
- Safety Clamp
- Instrumentation
- 2 – Bit synchronous counter
- High Performance Logic for test systems
- Latch-up performance
- Control circuits
- Test & Measurement
- Computers
- Automotive
