CY74FCT2374ATQCTG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 20 |
| Weight | 125.786834mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT2374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 12mA |
| Number of Bits | 8 |
| Clock Frequency | 250MHz |
| Propagation Delay | 6.5 ns |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 15mA 12mA |
| Max Propagation Delay @ V, Max CL | 6.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY74FCT2374ATQCTG4 Overview
It is packaged in the way of 20-SSOP (0.154, 3.90mm Width). D flip flop is embedded in the Tape & Reel (TR) package. It is configured with Tri-State, Non-Invertedas an output. This trigger uses the value Positive Edge. Surface Mountmounts this electrical part. A supply voltage of 4.75V~5.25V is required for operation. A temperature of -40°C~85°C TAis used in the operation. There is D-Type type of electronic flip flop associated with this device. The 74FCTseries comprises this type of FPGA. This D flip flop should not have a frequency greater than 250MHz. D latch consists of 1 elements. As a result, it consumes 200μA quiescent current. A total of 20terminations have been recorded. It is a member of the 74FCT2374 family. The power source is powered by 5V. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Devices in the FCTfamily are electronic devices. A part of the electronic system is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. This device has the clock edge trigger type of Positive Edge. This device is part of the FF/Latchesbase part number family. 8bits are used in its design. Vsup reaches its maximum value at 5.25V. Normal operation requires a supply voltage (Vsup) above 4.75V. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. There are 5V power supplies attached to it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The output current of 12mA makes it feature maximum design flexibility. As of now, there are 8input lines.
CY74FCT2374ATQCTG4 Features
Tape & Reel (TR) package
74FCT series
20 pins
8 Bits
5V power supplies
CY74FCT2374ATQCTG4 Applications
There are a lot of Texas Instruments CY74FCT2374ATQCTG4 Flip Flops applications.
- High Performance Logic for test systems
- Count Modes
- Balanced 24 mA output drivers
- Digital electronics systems
- Control circuits
- Buffer registers
- Frequency Divider circuits
- Circuit Design
- Latch-up performance
- Modulo – n – counter
