CY74FCT2374CTSOCG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT2374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 12mA |
| Number of Bits | 8 |
| Clock Frequency | 250MHz |
| Propagation Delay | 5.2 ns |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 15mA 12mA |
| Max Propagation Delay @ V, Max CL | 5.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
CY74FCT2374CTSOCG4 Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. Package Tubeembeds it. T flip flop uses Tri-State, Non-Invertedas the output. It is configured with the trigger Positive Edge. Surface Mountis occupied by this electronic component. A voltage of 4.75V~5.25Vis used as the supply voltage. It is operating at a temperature of -40°C~85°C TA. D-Typedescribes this flip flop. In FPGA terms, D flip flop is a type of 74FCTseries FPGA. In order for it to function properly, its output frequency should not exceed 250MHz. There are 1 elements in it. During its operation, it consumes 200μA quiescent energy. It has been determined that there have been 20 terminations. D latch belongs to the 74FCT2374 family. A voltage of 5V provides power to the D latch. This T flip flop has a capacitance of 5pF farads at the input. It is a member of the FCTfamily of D flip flop. There is an electronic part that is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. In this device, the clock edge trigger type is Positive Edge. This part is included in FF/Latches. An electronic part designed with 8bits is used in this application. It reaches the maximum supply voltage (Vsup) at 5.25V. Normal operation requires a supply voltage (Vsup) above 4.75V. The system runs on a power supply of 5V watts. The flip flop contains 2ports. It offers maximum design flexibility with its output current of 12mA. In order for the chip to function, it has 8output lines.
CY74FCT2374CTSOCG4 Features
Tube package
74FCT series
20 pins
8 Bits
5V power supplies
CY74FCT2374CTSOCG4 Applications
There are a lot of Texas Instruments CY74FCT2374CTSOCG4 Flip Flops applications.
- Memory
- Event Detectors
- Computing
- Buffer registers
- Differential Individual
- ATE
- 2 – Bit synchronous counter
- Counters
- Storage Registers
- Cold spare funcion
