CY74FCT2374TSOCTG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT2374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 250MHz |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 15mA 12mA |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
CY74FCT2374TSOCTG4 Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. The package Tape & Reel (TR)contains it. Currently, the output is configured to use Tri-State, Non-Inverted. This trigger uses the value Positive Edge. Surface Mountmounts this electrical part. It operates with a supply voltage of 4.75V~5.25V. A temperature of -40°C~85°C TAis considered to be the operating temperature. D-Typedescribes this flip flop. The 74FCTseries comprises this type of FPGA. In order for it to function properly, its output frequency should not exceed 250MHz. The list contains 1 elements. As a result, it consumes 200μA quiescent current and is not affected by external forces. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. D latch belongs to the 74FCT2374 family. The power supply voltage is 5V. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. FCTis the family of this D flip flop. It is mounted in the way of Surface Mount. There are 20pins on it. The clock edge trigger type for this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The design is based on 8bits. It reaches 5.25Vwhen the maximum supply voltage (Vsup) is applied. It is imperative that the supply voltage (Vsup) is maintained above 4.75Vin order to ensure normal operation. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. It operates from 5V power supplies. There are 2 ports embedded in the flip flops. In order for the chip to function, it has 8output lines.
CY74FCT2374TSOCTG4 Features
Tape & Reel (TR) package
74FCT series
20 pins
8 Bits
5V power supplies
CY74FCT2374TSOCTG4 Applications
There are a lot of Texas Instruments CY74FCT2374TSOCTG4 Flip Flops applications.
- Shift registers
- Storage Registers
- Count Modes
- Counters
- EMI reduction circuitry
- Data Synchronizers
- 2 – Bit synchronous counter
- Computers
- Storage registers
- CMOS Process
