CY74FCT2573CTSOCE4
| Parameters | |
|---|---|
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Nominal Supply Current | 200μA |
| Current - Output | 12mA |
| Number of Bits | 8 |
| Propagation Delay | 4.7 ns |
| Quiescent Current | 100μA |
| Turn On Delay Time | 1.5 ns |
| Family | FCT |
| Logic Function | D-Type, Latch |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 12mA |
| Independent Circuits | 1 |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
CY74FCT2573CTSOCE4 Overview
In the SOIC package, it can be found as an embedded module. Rail/Tube is the packaging method. 8 Bits are used in the design of this electronic part. As far as this device is concerned, it has no terminations. In order to function, the supply voltage should be set to 5V. With 20 pins, it is equipped. It is part of the family of electronic devices called FCT. With the design of the board, there are only 20 pins. Mounting this electronic component follows the Surface Mount method. This device has 2 ports that can be connected to it. FF/Latches is the subcategory of this part. There are 5V power supplies attached to it. For maximum efficiency, the supply voltage should be set to 5V. Aquiescent current is consumed by 100μA without being affected by external forces. The superior flexibility of this circuit can be attributed to the use of 8 circuits. The low level output current is set to 12mA. -15mA represents the high level output current. A temperature below 85°C should be used for operation. A temperature greater than -40°C should be used as the operating temperature. There is a maximum voltage of 5.25V supported. A voltage of 4.75V is the minimum supply voltage required for it to operate. As for the logic IC it uses, it is a BUS DRIVER. The output current of this device is 12mA, which makes it a very flexible design element.
CY74FCT2573CTSOCE4 Features
SOIC package
8 Bits
20 pin count
20 pins
5V power supplies
CY74FCT2573CTSOCE4 Applications
There are a lot of Texas Instruments CY74FCT2573CTSOCE4 Latches applications.
- Up/down difference counting
- Parallel data storage
- Parallel data synchronization
- Stacked or Push-Down Registers
- Timers
- Bus system register with enable parallel lines at bus side
- Counters
- Flip-flops
- Digital bus buffer
- Registers
