CY74FCT823ATSOC
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Weight | 624.398247mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74FCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Subcategory | Bus Driver/Transceiver |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74FCT823 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 9 |
| Propagation Delay | 20 ns |
| Turn On Delay Time | 6 ns |
| Family | FCT |
| Logic Function | D-Type, Transceiver |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 20ns @ 5V, 300pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Power Supply Current-Max (ICC) | 0.2mA |
| Number of Input Lines | 9 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 15.4mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY74FCT823ATSOC Overview
The flip flop is packaged in 24-SOIC (0.295, 7.50mm Width). There is an embedded version in the package Tube. This output is configured with Tri-State, Non-Inverted. The trigger configured with it uses Positive Edge. Surface Mountis in the way of this electric part. The JK flip flop operates with an input voltage of 4.75V~5.25V volts. The operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. In this case, it is a type of FPGA belonging to the 74FCT series. D latch consists of 1 elements. During its operation, it consumes 200μA quiescent energy. The number of terminations is 24. The 74FCT823family includes it. The power source is powered by 5V. A JK flip flop with a 5pFfarad input capacitance is used here. In terms of electronic devices, this device belongs to the FCTfamily of devices. In this case, the electronic component is mounted in the way of Surface Mount. This board has 24 pins. This device has the clock edge trigger type of Positive Edge. The part you are looking for is included in Bus Driver/Transceiver. This flip flop is designed with 9 Bits. The system runs on a power supply of 5V watts. The flip flop has 2ports embedded within it. If high efficiency is desired, the supply voltage should be kept at 5V. It offers maximum design flexibility with its output current of 64mA. 9input lines are available for you to choose from.
CY74FCT823ATSOC Features
Tube package
74FCT series
24 pins
9 Bits
5V power supplies
CY74FCT823ATSOC Applications
There are a lot of Texas Instruments CY74FCT823ATSOC Flip Flops applications.
- Supports Live Insertion
- Buffered Clock
- Bus hold
- Synchronous counter
- Load Control
- Safety Clamp
- Frequency Dividers
- Memory
- Guaranteed simultaneous switching noise level
- Shift Registers
