CY74FCT823BTPC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 24-DIP (0.300, 7.62mm) |
| Number of Pins | 24 |
| Weight | 1.753503g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74FCT823 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 9 |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 6 ns |
| Family | FCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 15ns @ 5V, 300pF |
| Prop. Delay@Nom-Sup | 7.5 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Input Lines | 9 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 83300000Hz |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY74FCT823BTPC Overview
24-DIP (0.300, 7.62mm)is the way it is packaged. The package Tubecontains it. The output it is configured with uses Tri-State, Non-Inverted. Positive Edgeis the trigger it is configured with. This electronic part is mounted in the way of Through Hole. A 4.75V~5.25Vsupply voltage is required for it to operate. Currently, the operating temperature is -40°C~85°C TA. It is an electronic flip flop with the type D-Type. The FPGA belongs to the 74FCT series. A total of 1elements are contained within it. As a result, it consumes 200μA quiescent current and is not affected by external forces. In 24terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. You can search similar parts based on 74FCT823. An input voltage of 5Vpowers the D latch. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In terms of electronic devices, this device belongs to the FCTfamily of devices. The electronic part is mounted in the way of Through Hole. There are 24pins on it. The clock edge trigger type for this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. This flip flop is designed with 9 Bits. A total of 5V power supplies are needed to run it. The flip flop contains 2ports. The supply voltage should be maintained at 5V for high efficiency. A total of 9input lines have been provided.
CY74FCT823BTPC Features
Tube package
74FCT series
24 pins
9 Bits
5V power supplies
CY74FCT823BTPC Applications
There are a lot of Texas Instruments CY74FCT823BTPC Flip Flops applications.
- QML qualified product
- Guaranteed simultaneous switching noise level
- ATE
- Asynchronous counter
- 2 – Bit synchronous counter
- Load Control
- Buffered Clock
- Memory
- Matched Rise and Fall
- Frequency Divider circuits
