CY74FCT823CTSOC
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Weight | 624.398247mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74FCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Termination | SMD/SMT |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74FCT823 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 9 |
| Propagation Delay | 12.5 ns |
| Turn On Delay Time | 6 ns |
| Family | FCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 12.5ns @ 5V, 300pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Power Supply Current-Max (ICC) | 0.2mA |
| Number of Input Lines | 9 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Max Frequency@Nom-Sup | 83300000Hz |
| Height | 2.65mm |
| Length | 15.4mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY74FCT823CTSOC Overview
24-SOIC (0.295, 7.50mm Width)is the way it is packaged. As part of the package Tube, it is embedded. T flip flop uses Tri-State, Non-Invertedas its output configuration. It is configured with the trigger Positive Edge. The electronic part is mounted in the way of Surface Mount. The supply voltage is set to 4.75V~5.25V. In the operating environment, the temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. It is a type of FPGA belonging to the 74FCT series. In total, there are 1 elements. As a result, it consumes 200μA of quiescent current without being affected by external factors. There are 24 terminations,The 74FCT823 family contains it. An input voltage of 5Vpowers the D latch. This JK flip flop has a 5pFfarad input capacitance. A device of this type belongs to the family of FCT. In this case, the electronic component is mounted in the way of Surface Mount. This board has 24 pins. In this device, the clock edge trigger type is Positive Edge. It is included in FF/Latches. 9bits are used in its design. An electrical current of 5V volts is applied to it. The flip flop has 2ports embedded within it. For high efficiency, the supply voltage should be set to 5V. With an output current of 64mA, this device offers maximum design flexibility. It is reported that there are 9 input lines.
CY74FCT823CTSOC Features
Tube package
74FCT series
24 pins
9 Bits
5V power supplies
CY74FCT823CTSOC Applications
There are a lot of Texas Instruments CY74FCT823CTSOC Flip Flops applications.
- Reduced system switching noise
- Single Down Count-Control Line
- ATE
- Bounce elimination switch
- CMOS Process
- Cold spare funcion
- Divide a clock signal by 2 or 4
- Memory
- Digital electronics systems
- Buffer registers
