DG1412EN-T1-GE4
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.8Ohm |
| Technology | CMOS |
| Terminal Position | QUAD |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG1412 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 24V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~24V ±4.5V~15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 15V |
| -3db Bandwidth | 210MHz |
| On-State Resistance (Max) | 1.8Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 550pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 24pF |
| On-state Resistance Match-Nom | 0.08Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | -20pC |
| Channel-to-Channel Matching (ΔRon) | 80m Ω |
| Crosstalk | -100dB @ 1MHz |
| Switch-on Time-Max | 510ns |
| Switch-off Time-Max | 380ns |
| Height Seated (Max) | 0.95mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG1412EN-T1-GE4 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-VQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. Multiplexers built on a SPST - NO switching circuit are built. There are 4 circuits in this switch device. DG1412 can be used to search for analog multiplexer variants. An switch multiplexer with 1.8Ohm internal resistance has a value of 1.8Ohm. Please refer to the datasheets for 16 pins functions. A voltage higher than 24V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. There should be 4.5V voltage fed to the electrical part below 4.5V. When the digital multiplexer is charged above 1μA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 15V. You should attach at least 4.5V voltage if you are using dual power supply.
DG1412EN-T1-GE4 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 210MHz
DG1412EN-T1-GE4 Applications
There are a lot of Vishay Siliconix DG1412EN-T1-GE4 Analog Switches & Multiplexers ICs applications.
- Industrial
- Cable PC
- E1 Multiplexer
- Microprocessor Controlled Analog Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Wireless Local Loop
- Industrial control systems
- DSUs
- Modems
- Central office
