DG2001DV-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Number of Pins | 6 |
| Weight | 19.986414mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 7Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 570mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2001 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Power Dissipation | 570mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 37 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 27 ns |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 900pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 20ns, 10ns |
| Charge Injection | 7pC |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 53ns |
| Switch-off Time-Max | 33ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 1mm |
| Length | 3.05mm |
| Width | 1.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2001DV-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a SOT-23-6 Thin, TSOT-23-6. The advanced packaging method Tape & Reel (TR) provides high reliability. A switch device like this is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. A total of 6 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 2V volts, the electrical component should be turned on and run. A total of 6 pins are injected into the electrical part body. The analog switch ics are built using SPDT switching circuits. Look for analog switch ic variants by searching with DG2001. Internally, this switch multiplexer has a resistance of 7Ohm. To find out what the functions of 6 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. A low voltage of 1.8V should be applied to the electronic component. 10nA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. A 1 input needs to be operated. A analog switch ics with 2 outputs is included.
DG2001DV-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG2001DV-T1-E3 Applications
There are a lot of Vishay Siliconix DG2001DV-T1-E3 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- ATM
- MP3 players
- Residential Gateways, Home Gateway/Router
- Cable PC
- Low-Voltage
- Mechanical reed relay replacement
- New designs requiring multiplexer functions
- Microwave transmission systems
- Precision test equipment
