DG2002DL-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2017 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 7.8Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2002 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 31 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 17 ns |
| On-State Resistance (Max) | 7.8Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 8ns, 6ns |
| Charge Injection | 5pC |
| Crosstalk | -69dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 1mm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG2002DL-T1-E3 Overview
This electronic part is conveniently packaged in 6-TSSOP, SC-88, SOT-363, making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. 6 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. Powered by a 2V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 6 series. These analog multiplexers are built based on SPDT switching circuits. Look for analog switch ic variants by searching with DG2002. Analog switches have 7.8Ohm internal resistance. Datasheets for 6 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. 1.8V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 10nA. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. Among the inputs that can be operated are the 1 inputs. An output of 2 is provided by the digital multiplexer.
DG2002DL-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG2002DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG2002DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- Routers
- Fault Tolerant Systems
- Industrial and process control systems
- E1 Multiplexer
- RGB switches
- Isolation
- PCMCIA cards
- PBX interfaces
- Multiplexers
- Precision test equipment
