DG2004DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Supplier Device Package | 8-MSOP |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 2.5Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 320mW |
| Base Part Number | DG2004 |
| Number of Outputs | 2 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 20nA |
| Power Dissipation | 320mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 28 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 22 ns |
| On-State Resistance (Max) | 2.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 51pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 28ns, 22ns |
| Charge Injection | 1pC |
| Crosstalk | -67dB @ 1MHz |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2004DQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~85°C TA. Due to its 2 channels, the electrical component produces high-quality output. A SPST - NC switching circuit is used to build these analog multiplexers. A total of 2 circuits make up this switch device. Look for analog switch ic variants by searching with DG2004. The internal resistance of this digital multiplexer is 2.5Ohm. For details about the functions of 8 pins, please refer to the datasheets. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.8V. The switch device would be able to operate with 20nA current. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. In order to operate the 2 inputs, there are several steps to follow. In an environment with a temperature higher than 85°C, the digital switches should not operate. A analog switch ics with 2 outputs is included. It is offered by suppliers in package 8-MSOP.
DG2004DQ-T1-E3 Features
2 Channels
Switch Circuit: SPST - NC
20nA Supply Current
DG2004DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2004DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- Private Branch Exchange (PBX)
- Avionics
- Ultrasound
- SONET
- Relay replacements
- Digital cross connects (DSX-1)
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Mechanical reed relay replacement
- Fault Tolerant Systems
