DG200ACJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 825mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG200A |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 180μA |
| Nominal Supply Current | 180μA |
| Max Supply Current | 180μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Charge Injection | 10pC |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG200ACJ Overview
Shipping overseas is convenient with the electronic component packed in 14-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around 0°C~70°C TA. 14 terminations have been made so far. High-quality output is provided by the electronic component's 2 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. The electronic part body is injected with 14 pins. A SPST - NC switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with DG200A. Analog switches have 70Ohm internal resistance. Datasheets for 14 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. An effective Dual supply digital multiplexer. 9V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 180μA current. When the digital multiplexer is charged above 180μA, damage can occur. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. If you are using dual power supplies, you should attach at least 4.5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A voltage of 18V can be used to operate the electronic component.
DG200ACJ Features
2 Channels
Switch Circuit: SPST - NC
180μA Supply Current
DG200ACJ Applications
There are a lot of Maxim Integrated DG200ACJ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- PDH Multiplexers
- Switching Systems
- Routers
- Digital Cross-Connects
- Communication systems
- Cross Connects
- CSU
- Avionics test equipment
- Video switching
