DG200ACY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG200A |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 180μA |
| Max Supply Current | 300μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Charge Injection | 10pC |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG200ACY Overview
This electronic part is conveniently packaged in 14-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around 0°C~70°C TA. In total, 14 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. An electrical component of this type can be found in the 14 series. Circuits based on SPST - NC switching are used to construct these analog switch ics. 2 circuits are used in this analogue multiplexer. Using the DG200A search parameter, you can discover variants of the switch. Internally, this switch multiplexer has a resistance of 70Ohm. To find out what the functions of 14 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 18V in normal situations. The analog switch ic is of the Dual supply type and is cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. For this digital switch to work, 180μA current would suffice. It may damage the digital multiplexer if the voltage is higher than 300μA. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 4.5V to your dual power supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG200ACY Features
1 Channels
Switch Circuit: SPST - NC
180μA Supply Current
DG200ACY Applications
There are a lot of Maxim Integrated DG200ACY Analog Switches & Multiplexers ICs applications.
- FTTH
- Industrial and process control systems
- High speed data transmission line cards
- Mechanical reed relay replacement
- Routers
- Signal routing between systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Communication systems
- Fiber to the Home
- Industrial
