DG200ADY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG200A |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 180μA |
| Nominal Supply Current | 200μA |
| Max Supply Current | 500μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Charge Injection | 10pC |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG200ADY Overview
The electrical component comes in 14-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Extended operating temperature around -40°C~85°C TA. 14 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. 14 pins are injected to the electronic part body. These analog multiplexers are built based on SPST - NC switching circuits. There are 2 circuits in this multiplexer. Try searching for the analog switch ic with DG200A if you are looking for variants. As far as internal resistance is concerned, it has 70Ohm. For details about the functions of 14 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. An effective Dual supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 9V. The switch device would be able to operate with 180μA current. The analogue multiplexer may be damaged if voltage is greater than 500μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. With dual power supplies, you should attach at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 15V operating voltages are supported by the electronic component.
DG200ADY Features
1 Channels
Switch Circuit: SPST - NC
180μA Supply Current
DG200ADY Applications
There are a lot of Maxim Integrated DG200ADY Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Avionics
- Sample-and-hold systems
- Audio and video switching
- E1 Multiplexer
- Microwave transmission systems
- Microprocessor controlled systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Industrial control systems
- PDAs
