DG200BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 1.620005g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 470mW |
| Max Supply Current | 50μA |
| Turn On Delay Time | 1 μs |
| Number of Inputs | 2 |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 425 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Drain to Source Resistance | 70Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 19.3mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
DG200BDJ Overview
Shipping overseas is convenient due to the electrical component's packing in 14-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. This analog switch is mounted in Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Total terminations are 14. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A key feature of the 14 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPST - NC switching circuits. An switch multiplexer with 85Ohm internal resistance has a value of 85Ohm. To find out what the 14 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. An effective Dual supply digital multiplexer. A low voltage of 13V should be applied to the electronic component. If you put voltage higher than 50μA on the digital multiplexer, damage may occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. It is recommended that you attach at least 7V to your dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. 15V operating voltages can be used with this electrical part. There are 2 inputs to be operated. A Drain to Source resistance of 70Ohm is shown for this electronic part.
DG200BDJ Features
Switch Circuit: SPST - NC
Drain-to-Source resistance: 70Ohm
DG200BDJ Applications
There are a lot of Vishay Siliconix DG200BDJ Analog Switches & Multiplexers ICs applications.
- Ultrasound
- PCMCIA cards
- Public switching systems
- Automatic test equipment
- Sample hold systems
- Remote wireless modules
- Fault Tolerant Systems
- Audio signal routing
- Multi-Line E1 Interface Cards
- Medical systems
