DG200BDJ-E3
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 19.3mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 1.620005g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 85Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | DG200 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 50μA |
| Nominal Supply Current | 50μA |
| Power Dissipation | 470mW |
| Max Supply Current | 50μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Number of Inputs | 2 |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 425 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
DG200BDJ-E3 Overview
Due to its 14-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~85°C TA. The total number of terminations is 14. A high-quality output is provided by the electrical component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 14 series. The analog switch ics are built using SPST - NC switching circuits. Using the DG200 search parameter, you can discover variants of the switch. There is 85Ohm internal resistance in this digital multiplexer. You can find the functions of the 14 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. The analog switch ic is of the Dual supply type and is cost-effective. 13V is the lowest voltage the electrical component should receive. This digital switch can be operated with a current of 50μA. A digital multiplexer may suffer damage if voltage is applied above 50μA. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. This electrical part is compatible with 15V operating voltages. In order to operate the 2 inputs, there are several steps to follow.
DG200BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
50μA Supply Current
DG200BDJ-E3 Applications
There are a lot of Vishay Siliconix DG200BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Frame Relay Equipment
- Communication systems
- Precision test equipment
- Microprocessor Controlled Analog Systems
- Medical Instrumentation
- Relay replacements
- Fault Tolerant Systems
- Imaging
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
