DG2012DL-T1-E3
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1.8Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2012 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 63 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 45 ns |
| On-State Resistance (Max) | 1.8Ohm |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF |
| On-state Resistance Match-Nom | 0.25Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 38ns, 32ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 250m Ω (Max) |
| Crosstalk | -64dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 1Ohm |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Contact Plating | Tin |
| Mount | Surface Mount |
DG2012DL-T1-E3 Overview
Packed in 6-TSSOP, SC-88, SOT-363, the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. A total of 6 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 2V voltage supply. This electrical component is included in the 6 series of products. These analog multiplexers are built based on SPDT switching circuits. Look for analog switch ic variants by searching with DG2012. This digital multiplexer has 1.8Ohm internal resistance. The datasheets for the 6 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Digital switch that provides Single power at a cost-effective price. A low voltage of 1.8V should be applied to the electronic component. This digital switch can be operated with a current of 10nA. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to operate 1 inputs. Drain to Source resistance for this electronic component is 1Ohm. An output of 2 is provided by the digital multiplexer.
DG2012DL-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
Drain-to-Source resistance: 1Ohm
DG2012DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG2012DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Isolation
- New designs requiring multiplexer functions
- E1 Multiplexer
- E1 Network Equipment
- Audio signal routing
- Imaging
- Sample hold systems
- PDAs
- Microwave transmission systems
