Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-VQFN Exposed Pad |
Number of Pins |
16 |
Weight |
57.09594mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2016 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
1.6Ohm |
Terminal Finish |
PALLADIUM GOLD OVER NICKEL |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
1.88W |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG2015 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
3V |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
3.3V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
65 ns |
Supply Type |
Single |
Turn-Off Delay Time |
60 ns |
On-State Resistance (Max) |
1.6Ohm |
Multiplexer/Demultiplexer Circuit |
2:2 |
Off-state Isolation-Nom |
67 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
67pF |
On-state Resistance Match-Nom |
0.15Ohm |
Switch Circuit |
DPDT |
Switch Time (Ton, Toff) (Max) |
40ns, 35ns |
Charge Injection |
7pC |
Channel-to-Channel Matching (ΔRon) |
150m Ω |
Crosstalk |
-70dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
67ns |
Voltage - Supply, Single (V+) |
2.7V~3.3V |
Height |
950μm |
Length |
4mm |
Width |
4mm |
RoHS Status |
ROHS3 Compliant |
DG2015DN-T1-E4 Overview
Packed in 16-VQFN Exposed Pad, the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. 2:2 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. A 2 channel electronic part produces high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. It is injected into the electrical part body with 16 pins. On the other hand, analog switches can be constructed using DPDT switching circuits. There are 2 circuits in this multiplexer. Use DG2015 to search for variants of the digital switches. As far as internal resistance is concerned, it has 1.6Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 3.3V. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 2.7V. 1μA current would be enough for this multiplexer to operate. An analogue multiplexer drains from a single voltage supply at 2.7V~3.3V. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG2015DN-T1-E4 Features
2 Channels
Switch Circuit: DPDT
1μA Supply Current
DG2015DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2015DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Relay replacements
- High-Voltage
- Industrial control systems
- Industrial and process control systems
- Sample hold systems
- USB 1.1 signal switching circuits
- High speed data transmission line cards
- Frame Relay Equipment
- ISDN NT1/TA