DG2018DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VFQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 8Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexers or Switches |
| Max Power Dissipation | 850mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2018 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Power Dissipation | 850mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 48 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 33 ns |
| -3db Bandwidth | 180MHz |
| On-State Resistance (Max) | 8Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 54 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 48ns, 33ns |
| Charge Injection | -2.46pC |
| Channel-to-Channel Matching (ΔRon) | 600m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 65ns |
| Switch-off Time-Max | 35ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 900μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2018DN-T1-E4 Overview
The electrical component comes in 16-VFQFN Exposed Pad packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 2:2 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. Totally, there are 16 terminations. A electrical component with 2 channels is capable of high-quality output. When a voltage supply of 3V is used, the electronic component should be turned on and run. 16 pins are injected to the electronic part body. Based on DPDT switching circuits, these analog multiplexers work. There are 2 circuits in this multiplexer. Try searching for DG2018 variants of the analog switch ic. As far as internal resistance is concerned, it has 8Ohm. Please refer to the datasheets for 16 pins functions. There is Multiplexers or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. An operating current of 10nA would be sufficient for this switch device. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 1μA. In order to operate the 4 inputs, there are several steps to follow. The analog switch ics includes 8 outputs.
DG2018DN-T1-E4 Features
2 Channels
Switch Circuit: DPDT
10nA Supply Current
-3db Bandwidth: 180MHz
DG2018DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2018DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Sample-and-hold systems
- SONET
- Industrial control systems
- PBXs
- Switching Systems
- Access Concentrators
- Central office
- Precision instrumentation
- Routers
