DG2019DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VFQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 8Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexers or Switches |
| Max Power Dissipation | 850mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2019 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Power Dissipation | 850mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 48 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 33 ns |
| -3db Bandwidth | 180MHz |
| On-State Resistance (Max) | 8Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 54 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 48ns, 33ns |
| Charge Injection | -2.46pC |
| Channel-to-Channel Matching (ΔRon) | 600m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 65ns |
| Switch-off Time-Max | 35ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 900μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2019DN-T1-E4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-VFQFN Exposed Pad. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature extended to -40°C~85°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. The electronic part body is injected with 16 pins. Unlike digital switches, these are based on SPDT switching circuits. Try searching for the analog switch ic with DG2019 if you are looking for variants. In this multiplexer, the internal resistance is 8Ohm. To find out what the 16 pins do, please refer to the datasheets. There is a standard Multiplexers or Switches analogue multiplexer here. Multiplexers should not be powered above 5.5V in normal situations. Analog switch ics with Single supply type are cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 10nA current. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. The analogue multiplexer may be damaged if voltage is greater than 1μA. The 4 inputs need to be operated in order to work. The analog switch ics includes 8 outputs.
DG2019DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
-3db Bandwidth: 180MHz
DG2019DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2019DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Intelligent PBX
- Frame Relay Equipment
- Precision data acquisition
- Microprocessor controlled systems
- Modems
- Voice over IP/DSL – Integrated Access Devices, Smart
- PBXs
- Industrial control systems
