DG201AAK
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-CERDIP |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2009 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 175Ohm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Max Power Dissipation | 900mW |
| Number of Outputs | 4 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 900mW |
| Max Supply Current | 2mA |
| Turn On Delay Time | 600 ns |
| Number of Inputs | 4 |
| Supply Type | Dual |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Drain to Source Resistance | 175mOhm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.94mm |
| Length | 19.56mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
DG201AAK Overview
The electronic component is convenient to ship overseas because it is packed in a 16-CDIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -55°C~125°C TA are extended for operation. High-quality output is provided by the electronic component's 4 channels. Circuits based on SPST - NC switching are used to construct these analog switch ics. A total of 4 circuits make up this switch device. There is 175Ohm internal resistance in this digital multiplexer. Datasheets for functions of 16 pins are available. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. A cost-effective Dual supply type analogue multiplexer. The lowest voltage the electronic part should receive is 13V. Putting voltage greater than 2mA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIn the case of dual power supplies, you should connect at least 7V. It can operate from 15V operating voltages. Operating the 4 inputs requires 4 inputs. A temperature above 125°C is not suitable for operation of the analogue multiplexer. A Drain to Source resistance of 175mOhm is shown for this electronic part. This digital multiplexer has 4 outputs. Suppliers offer the 16-CERDIP package.
DG201AAK Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 175mOhm
DG201AAK Applications
There are a lot of Vishay Siliconix DG201AAK Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- Ultrasound
- Channelized and Unchannelized DS3 applications
- PCMCIA cards
- Optical Applications
- Microprocessor Controlled Analog Systems
- Central office
- Remote Powered Equipment
- 65 V DACs
- DSLAMs
