DG201AAK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 16 |
| JESD-30 Code | R-GDIP-T16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Max Supply Current | 500μA |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Screening Level | MIL-STD-883 Class B |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG201AAK/883B Overview
This electronic part is conveniently packaged in 16-CDIP (0.300, 7.62mm), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Around -55°C~125°C TA is the extended operating temperature. The total number of terminations is 16. This electronic part offers high-quality output due to its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the electrical part body. A SPST - NC switching circuit is used for these analog switches. There are 4 circuits in this multiplexer. This digital multiplexer has 175Ohm internal resistance. To find out what the functions of 14 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. A analog switch ic that has a cost-effective Dual, Single supply type. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. This electrical part is compatible with 18V operating voltages.
DG201AAK/883B Features
1 Channels
Switch Circuit: SPST - NC
DG201AAK/883B Applications
There are a lot of Maxim Integrated DG201AAK/883B Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- DVD-R
- Video signal routing
- Cable PC
- Relay Replacement
- Remote Powered Equipment
- Automatic test equipment
- Signal routing between systems
- E1 Network Equipment
- Ultrasound
