DG201ACJ+
| Parameters | |
|---|---|
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG201A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
DG201ACJ+ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. In Through Hole, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around 0°C~70°C TA. 16 terminations have been made so far. Due to its 4 channels, the electrical component produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Multiplexers built on a SPST - NC switching circuit are built. Try searching with DG201A to find analog multiplexer variants. It has an internal resistance of 200Ohm. The datasheets for the 16 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual supply type. 20μA current would be enough for this multiplexer to operate. Putting voltage greater than 20μA on the multiplexer may cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. If you are using a dual power supply, you should attach at least 4.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating voltages of 15V are compatible with the electrical part.
DG201ACJ+ Features
4 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG201ACJ+ Applications
There are a lot of Maxim Integrated DG201ACJ+ Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- Modems
- Cable PC
- Signal routing between systems
- DSUs
- Relay Replacement
- Intelligent PBX
- Precision test equipment
- Channel Banks
- Audio and video routing
