DG201ACSE
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG201A |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG201ACSE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around 0°C~70°C TA. In total, there have been 16 terminations. A electrical component with 4 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. Electronic part bodies are injected with 16 pins. A SPST - NC switching circuit is used to build these analog multiplexers. Try searching for DG201A variants of the analog switch ic. Analog switches have 200Ohm internal resistance. Please refer to the datasheets for 16 pins functions. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. The digital multiplexer has a low cost Dual supply. The analogue multiplexer could operate on 20μA current. Putting voltage greater than 20μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. It is recommended that you attach at least 4.5V to your dual power supply. The electrical part can be operated at 18V voltage levels.
DG201ACSE Features
4 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG201ACSE Applications
There are a lot of Maxim Integrated DG201ACSE Analog Switches & Multiplexers ICs applications.
- Transmit
- Fiber In The Loop (FITL)
- Microwave transmission systems
- RGB switches
- Avionics test equipment
- PBXs
- Fault Tolerant Systems
- Communications systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Modems
