DG201ADJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG201A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 30mA |
| Max Supply Current | 30mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG201ADJ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. This electronic part can be found in the 16 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. The multiplexer consists of 4 circuits. DG201A can be used to search for analog multiplexer variants. Analog switches have 200Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 18V voltage to the switch device. An effective Dual supply digital multiplexer. The lowest voltage the electronic part should receive is 4.5V. In order to operate this switch device, it would need a current of 20μA. The analogue multiplexer may be damaged if voltage is greater than 30mA. There is no problem with using dual supply voltage, but it should not exceed 18V. The voltage should be at least 4.5V if you are using dual power supplies. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG201ADJ Features
1 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG201ADJ Applications
There are a lot of Maxim Integrated DG201ADJ Analog Switches & Multiplexers ICs applications.
- Communication systems
- High speed data transmission line cards
- Communications systems
- MP3 players
- Frame Relay Equipment
- Data Acquisition Systems
- Routers
- Imaging
- Audio/video switches
- Cross Connects
