DG201ADY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG201A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 600ns |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG201ADY Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. As a result of its 4 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 16 pins. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Try searching for DG201A variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 200Ohm. For functions related to 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 25V to a switch device. A analog switch ic that has a cost-effective Dual supply type. This multiplexer would work with 20μA current. A voltage higher than 100μA may cause damage to the switch multiplexer. There is no problem with using dual supply voltage, but it should not exceed 18V. For dual power supplies, a voltage of at least 4.5V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Operating voltages range from 18V.
DG201ADY Features
4 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG201ADY Applications
There are a lot of Maxim Integrated DG201ADY Analog Switches & Multiplexers ICs applications.
- SDH
- Multiplexers
- Audio and video routing
- Audio and video signal routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multi-Line E1 Interface Cards
- Digital Cross-Connects
- Wireless Local Loop
- DSLAMs
- Industrial
