DG201ADY+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG201A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 600ns, 450ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG201ADY+T Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. A SPST - NC switching circuit is used to build these analog multiplexers. This multiplexer is composed of 4 circuits. Try searching with DG201A to find analog multiplexer variants. A 200Ohm internal resistance characterizes this multiplexer. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. The digital multiplexer has a low cost Dual supply. It would be sufficient to run this analogue multiplexer with 20μA current. When the digital multiplexer is charged above 100μA, damage can occur. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. If you are using a dual power supply, you should attach at least 4.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 15V operating voltages can be used with this electrical part.
DG201ADY+T Features
1 Channels
Switch Circuit: SPST - NC
20μA Supply Current
DG201ADY+T Applications
There are a lot of Maxim Integrated DG201ADY+T Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- DVD-R
- Optical Applications
- Public switching systems
- Fiber In The Loop (FITL)
- Audio and video switching
- PBXs
- Fiber to the Home
- Communication systems
