DG201BAK
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 900mW |
| Max Supply Current | 50μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG201BAK Overview
The electronic component is convenient to ship overseas because it is packed in a 16-CDIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. It is mounted in the position Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -55°C~125°C TA degrees Celsius. Total terminations are 16. With a 15V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. Based on SPST - NC switching circuits, these analog multiplexers work. This digital multiplexer has 85Ohm internal resistance. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 25V. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 50μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. It is recommended that you attach at least 4.5V to your dual power supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating the 4 inputs requires 4 inputs.
DG201BAK Features
Switch Circuit: SPST - NC
DG201BAK Applications
There are a lot of Vishay Siliconix DG201BAK Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Channelized and Unchannelized DS3 applications
- Microprocessor Controlled Analog Systems
- Multiplexers
- Medical
- Residential Gateways, Home Gateway/Router
- Access Concentrators
- 65 V DACs
- Sample hold systems
- Relay replacements
