DG201BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 470mW |
| Max Supply Current | 50μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4.5V~25V ±4.5V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 85Ohm |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
DG201BDJ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. Through Hole is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 16. When the electronic component is given a voltage of 15V, it should be turned on and run. This electronic part can be found in the 16 series. Unlike digital switches, these are based on SPST - NC switching circuits. A 85Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 25V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 4.5V. When the digital multiplexer is charged above 50μA, damage can occur. For this switch, a dual supply voltage is feasible, but it must not exceed 22VYou should attach at least 4.5V voltage if you are using dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. There are 4 inputs to be operated. It has a Drain to Source resistance of 85Ohm ohms.
DG201BDJ Features
Switch Circuit: SPST - NC
Drain-to-Source resistance: 85Ohm
DG201BDJ Applications
There are a lot of Vishay Siliconix DG201BDJ Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- SDH
- Medical systems
- Multiplexers
- SONET
- Cable Modem
- Multi-Line E1 Interface Cards
- Access Concentrators
- Medical
- Channel Banks
