Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Weight |
1.627801g |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2005 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
85Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG201 |
Pin Count |
16 |
Polarity |
Inverting |
Power Supplies |
12/+-15V |
Number of Channels |
1 |
Max Supply Voltage |
25V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
50μA |
Nominal Supply Current |
100μA |
Power Dissipation |
470mW |
Max Supply Current |
50μA |
Throw Configuration |
SPST |
Turn On Delay Time |
300 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
4.5V~25V ±4.5V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
300ns, 200ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
85Ohm |
Normal Position |
NC |
Height |
3.81mm |
Length |
21.33mm |
Width |
7.11mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG201BDJ-E3 Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Through Hole, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. This electrical component is included in the 16 series of products. SPST - NC switching circuits are used in these analog switch ics. Try searching with DG201 to find analog multiplexer variants. An switch multiplexer with 85Ohm internal resistance has a value of 85Ohm. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. An effective Dual, Single supply digital multiplexer. 4.5V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 50μA current would be sufficient. When the digital multiplexer is charged above 50μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. It is recommended that you attach at least 4.5V to your dual power supply. Among the inputs that can be operated are the 4 inputs. There is 85Ohm resistance between Drain and Source for this electronic part.
DG201BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
50μA Supply Current
Drain-to-Source resistance: 85Ohm
DG201BDJ-E3 Applications
There are a lot of Vishay Siliconix DG201BDJ-E3 Analog Switches & Multiplexers ICs applications.
- HDTV
- Switching Systems
- Audio and video signal routing
- DSUs
- USB 1.1 signal switching circuits
- Medical systems
- Automatic test equipment
- ISDN NT1/TA
- Cellular phones
- Public switching systems